• <ruby id="swuwg"><i id="swuwg"></i></ruby>

    <span id="swuwg"></span>
  • <ol id="swuwg"></ol>
      <legend id="swuwg"><li id="swuwg"></li></legend>

      —— 朗菲電氣·您的首選! ——

      產品中心
      相序保護器系列 時間繼電器 溫度控制器 電動機保護器 交流接觸器系列 熱過載繼電器系列 整流器系列 高低壓電氣元器件

      產品詳情

      適用范圍 Applicable scope

              JR28系列熱過載繼電器(以下簡稱繼電器)主要用于交流50Hz(60Hz),額定工作電壓660V及以下,額定工作電流0.10-93A的電路中,作作電路和電動機的過載、斷相、啟動時間過長和堵轉時間過長的保護。

              熱繼電器具有斷相保護、溫度補償、整定電流調節、自動復位和手動復位任意選擇、動作指示信號、動合、動斷輔助觸頭絕緣分開、安裝面積小、安裝方式多樣等功能和特點,具有測試按鈕和停止按鈕??蛇M行動作靈活性檢查。有防止手指觸電護罩,使用安全。有閉鎖裝置防止誤操作等。

              執行標準:GB14048.4、IEC60947-4-1。

             JR28 series thermal overload relay (hereinafter referred to as the relay) is mainly used for AC 50Hz (60Hz), rated voltage 660V and below, the rated current of 0.10-93A circuit, as the circuit and motor overload, phase failure, start-up time Long and blocking the protection of the long time.

             Thermal relay with phase protection, temperature compensation, setting current regulation, automatic reset and manual reset any choice, the action instructions signal, moving together, broken off auxiliary contacts isolated insulation, installation area is small, the installation of a variety of functions and features, with Test button and stop button. Action flexibility check. Have to prevent finger electric shock shield, safe to use. A locking device to prevent misuse and so on.

             Executive Standard: GB14048.4, IEC60947-4-1.


      型號及其含義 Model and its meaning

      1.jpg


      使用環境條件 Use of environmental conditions

      ◇ 周圍空氣溫度:空氣溫度上限為+40℃;空氣溫度24h的平均值不超過+35℃;空氣溫度下限為-5℃。

      ◇ 安裝地點的海拔不超過2000m。

      ◇ 大氣相對濕度在周圍空氣+40℃時不超過50%,在較低溫度下可以有較高的相對濕度,最濕月平均最大相對濕度為90%,同時該月的月平均最低+25℃,并考慮到因溫度變化發生在產品上的凝露。

      ◇ 污染等級為3。

      ◇ 安裝類別Ⅲ類。

      ◇ 安裝位置應與垂直面的安裝傾斜度不超過5°;應安裝在無顯著振動和沖擊的地方。

      ◇ Ambient air temperature: the upper limit of air temperature is + 40 ℃; the average of air temp erature 24h does not exceed + 35 ℃; the lower limit of air temperature is -5 ℃.

      ◇ installation site elevation not exceeding 2000m.

      ◇ Ambient relative humidity in the surrounding air +40 ℃ does not exceed 50%, at lower temp eratures can have a higher relative humidity, the wettest month average maximum relative hum idity of 90%, while the monthly average minimum +25 ℃ , And taking into account the condens ation on the product due to temperature changes.

      ◇ pollution level is 3.

      ◇ installation category Ⅲ category.

      ◇ installation position should be installed with the vertical tilt of not more than 5 °; should be installed in the absence of significant vibration and impact of the place.


      主要技術參數 The main technical parameters

      ◇ 基本參數

      ◇ 主電路額定絕緣電壓AC660V;額定工作電流25A、36A、93A。

      ◇ 輔助電路額定絕緣電壓AC500V;額定頻率50、60Hz;使用類別、額定工作電壓、額定工作電流和額定發熱電流見表2。

      ◇ basic parameters

      ◇ main circuit rated insulation voltage AC660V; rated working current 25A, 36A, 93A.

      ◇ auxiliary circuit rated insulation voltage AC500V; rated frequency 50,60Hz; use category, rated working voltage, rated current and rated 

           current Table 2.

      ◇ 熱繼電器的額定工作電流、額定工作電流調節范圍、適配交流接觸器型號及推薦熔斷器型號見表1。

      ◇ thermal relay rated current, rated current adjustment range, suitable for AC contactor models and recommended fuse models in Table 1.

      2.jpg


      外形及安裝尺寸 Shape and installation dimensions

      3.jpg

      ◇ 熱繼電器在各項負載不平衡時的動作特性符合表4的規定。

      ◇ thermal relay in the load imbalance when the operating characteristics in line with the provisions of Table 4.

      4.jpg

      ◇ 復位性能  reset performance

      ◇ 熱繼電器動作后,手動復位時間不大于2min,自動復位時間不大于8min。

      ◇ thermal relay action, the manual reset time is not greater than 2min, automatic reset time is not greater than 8min.


      結構特征 Structure

      ◆ 熱繼電器的內部結構

      ◇ 熱繼電器的內部結構為安裝平面呈層式立體布置結構,即動作機構(支座)在前面,熱一雙元件在后面,這種結構的特點是:能與相應的交流接觸     器構成組合安裝,減少安裝面積;整定電流調節、復位、停止試驗諸按鈕及動作指示等功能組件,均可布置在蓋前的平面上,操作方面,功能     指示直觀。內部結構電氣示意見圖4。

      ◆ thermal relay internal structure

      ◇ The internal structure of the thermal relay for the installation plane was three-dimensional layout of the three-dimensional struc ture, that the action mechanism (support) in the front, a pair of hot elements in the back of this structure is characterized by: with the corresponding AC contactor combo installation, Reduce the installation area; adjust the current setting, reset, stop the test button and action instructions and other functional components, can be arranged in front of the plane, the operation, the function instructions intuitive. The internal structure of the electrical schematic shown in Figure 4.

      5.jpg

      ◆ 熱繼電器的基本工作原理

      ◇ 熱繼電器屬雙金屬片式,其熱元件與被保護對象的主電路串接,負載電流通過熱元件和雙金屬片(復式加熱),利用熱一雙元件的熱效應,使雙金屬片彎曲,但負載電流在其預置值(一般為保護對象的額定電流)1.2倍及以上時,熱一雙元件產生的熱量使雙金屬元件彎曲推動滑板使熱繼電器的動作機構脫扣,將電源切斷,被保護對象到保護。

      ◆ The basic working principle of thermal relay

      ◇ thermal relay is a bimetallic strip, the thermal element and the main circuit of the object being protected in series, the load current through the thermal element and the bimetal (duplex heating), the use of heat a double element of the thermal effect, so that the bimetallic bending, When the load current is 1.2 times or more of its preset value (usually the rated current of the protection obje ct), the heat generated by the hot and the double components causes the bimetallic component to flex and push the sliding plate to trip the thermal relay operating mechanism, and the power supply is cut off and protected Object to protection.


      安裝使用及維修 Installation and maintenance

      安裝使用

      熱繼電器的整定電流調節范圍應包容被保護對象的額定電流值。

      熱繼電器整定電流調節旋鈕不能隨意旋轉,使用時請按保護對象的電流值進行調節、整定,否則容易引起誤動作。

      選定組合安裝時,先適當松動接觸器主接線端子上的接線螺釘,把熱繼電器的掛鉤部分插入接觸器相慶的溝槽,再把熱繼電器的導電桿插入接觸器的主接線端子內,堅固主動接線端子上的螺釘,即可完成組合安裝。

      選定分立安裝,首先按5.1.3程序將熱繼電器固定在附件(底板)上,即可進行分立安裝。

      連接導線采用單芯聚氯乙烯(PVC)絕緣銅導線,輔助電路連接導線截面積1mm2,主電路連接導線載面積見表5,負載為電動機時的接線原理圖見圖5。

      Installation and use

      The setting range of the setting current of thermal relay should include the rated current value of the protected object.

      Thermal relay setting current adjustment knob can not be freely rotated, please use the current value of the protection object to adjust, set, othe rwise easily lead to malfunction.

      When the selected combination is installed, loosen the connection screw on the main contact of the contactor, insert the hook part of the thermal relay into the groove of the contactor, insert the conductive rod of the thermal relay into the main terminal of the contactor, Firmly screw the active terminals to complete the combined installation.

      Selected discrete installation, first press the 5.1.3 program will be fixed in the thermal relay attachment (backplane), can be installed separately.

      The connecting wire is made of single-core PVC insulated copper wire. The cross-sectional area of the auxiliary circuit connecting wire is 1mm2. The connection area of the main circuit connecting wire is shown in Table 5, and the wiring schematic diagram when the load is a motor is shown in Figure 5.

      6.jpg



      ,亚洲 自拍 色综合图区一,美女视频黄频a免费高清不卡,国产卡1卡2 卡三卡网站